+91 91488 711109 AM – 6 PM, all days Order now

BBQ & grilling

How to light charcoal without lighter fluid

Kerosene and lighter fluid leave a chemical taste on food and are the reason so many barbecues start with a cloud of black smoke. Here are five better ways, from the most reliable to the most improvised.

3 min read · Updated 14 November 2026 · By the Charcoals team, Bengaluru

Why skip the lighter fluid?

Lighter fluid and kerosene are petroleum products. If you cook before they have completely burnt off, the fumes settle on your food and you can taste them. They also flare unpredictably, which is how eyebrows get singed. Good charcoal does not need help: it just needs heat at the bottom and air flowing up through it.

Every method below works on one principle. Fire climbs. Put a small, steady flame under the charcoal, give it a path for air, and the coals light each other from the bottom up.

Method 1: The chimney starter (best)

A chimney starter is a metal cylinder with a grate near the bottom and a heat-proof handle. It is the method almost every serious grill cook uses, and it pays for itself within a few cooks.

  1. Stuff two or three loosely crumpled sheets of newspaper, or one or two fire starter cubes, into the space under the grate.
  2. Fill the top section with charcoal.
  3. Set it on the grill's lower grate and light the paper or cubes through the holes at the bottom.
  4. Wait 15 to 20 minutes. When the top pieces are edged with grey ash and glowing, the charcoal is ready.
  5. Holding the handle with a glove, pour the coals into the grill and spread them.
Why it works

The tall cylinder acts like a flue. Hot air rushes up through the charcoal, pulling fresh air in at the bottom, so every piece lights evenly and fast.

Method 2: Fire starter cubes

Fire starter cubes are small blocks of compressed wood fibre and wax that burn steadily for 8 to 10 minutes, long enough to get charcoal going. They are clean, odourless once burning, and work even when the charcoal is slightly damp.

  1. Place two or three cubes in the centre of the grill.
  2. Build a small pyramid of charcoal over them, leaving gaps for air.
  3. Light the cubes and leave the pile alone for 15 to 20 minutes.
  4. Once the pieces at the top are ashed over, spread the coals.

Method 3: Newspaper and a pyramid

If you have nothing else, newspaper works, though it needs more attention.

  1. Twist six to eight sheets of newspaper into loose knots or rings and place them in the grill.
  2. Pile charcoal over them in a pyramid, small pieces at the bottom.
  3. Light the paper in several places.
  4. If the paper burns out before the charcoal catches, gently fan the base with a piece of cardboard. A hand fan, the traditional vishiri, works perfectly.

Method 4: Electric starter or hot-air gun

An electric looped element pushed into the charcoal lights it in about 10 minutes with no flame and no smoke. A hot-air blower (sold for lighting barbecues) does it even faster. Both need a power socket near the grill, so they suit terraces and back gardens.

Method 5: Coconut husk and dry twigs

This is how charcoal has been lit in Indian kitchens for generations. Dry coconut husk fibre and a handful of dry twigs or a few pieces of dry wood catch quickly and burn hot. Lay them under the charcoal and light them the same way as newspaper.

How to tell when charcoal is ready

  • Colour: most pieces are covered in a thin layer of grey-white ash, with an orange glow beneath.
  • Smoke: the thick white smoke of lighting has stopped. Cook on smoky coals and food tastes acrid.
  • Heat: hold your palm 12 cm above the grate. Two seconds means high heat, five seconds means medium.

From lighting to cooking, allow 20 to 30 minutes. Starting too early is the most common beginner mistake. See our list of BBQ mistakes to avoid.

If your charcoal will not light

  • It is damp. Damp charcoal hisses, smokes and refuses to catch. Dry it in the sun for a few hours, and store it sealed and off the floor.
  • Not enough air. Open all the vents on the grill and make sure ash from last time is not blocking the bottom.
  • The pieces are packed too tightly. Rebuild the pile loosely so air can move through.
  • The pieces are too large. Start with smaller pieces at the bottom and add larger lumps once the fire is going.

Frequently asked questions

How long does charcoal take to be ready?

With a chimney starter or fire starter cubes, charcoal is ready to cook on in 15 to 20 minutes. With newspaper alone, allow 25 to 30 minutes.

Can I use kerosene to light charcoal?

It is better not to. Kerosene leaves a petroleum taste on food if it has not fully burnt off, flares unpredictably and produces thick black smoke. A chimney starter or fire starter cubes are cleaner and safer.

Can I light charcoal with a gas stove?

You can hold a single piece with tongs over a gas burner until it glows, then use it to light the rest, but never bring a bag or a pile of charcoal indoors. Light and burn charcoal outdoors only.

Should the grill lid be open or closed while lighting?

Open. A fire that is just starting needs as much air as possible. Close the lid once the coals are ready and the food is on.

Need charcoal or cooking wood?

Hardwood, coconut shell and BBQ charcoal, plus pizza, biryani and pooja wood. Same-day delivery in Bangalore, courier across India.

WhatsApp
Call Order on WhatsApp